AFM and DFM Disabler vs Tune: Keep Your GM V8 on All Eight Cylinders

Plug-in module or tune? How to stop GM Active and Dynamic Fuel Management, which module fits your truck, and when a tune is required.


By The Tuner Store
3 min read


There are two ways to keep a GM V8 out of Active Fuel Management (AFM) or Dynamic Fuel Management (DFM): a plug-in disabler module, or a tune that turns cylinder deactivation off. A module is the simple choice for a stock truck you want to keep stock. A tune makes sense if you're already tuning, or if you've removed the AFM or DFM hardware.

What AFM and DFM do

AFM shuts off half the cylinders of many 2007-2018 GM V8s under light load to save fuel. DFM, used on many 2019 and newer GM trucks and SUVs, can run on a varying number of cylinders. Common complaints are a shudder when cylinders drop, exhaust drone, and concern about lifter wear tied to cylinder deactivation.

Option 1: A plug-in disabler module

A module keeps the engine in full V8 mode without reprogramming the factory computer. It adds no power, and unplugging it returns the vehicle to stock behavior.

Module Fits Notes
Range AFM/DFM Disabler GM V6 and V8 cars, trucks and SUVs with AFM or DFM, before the 2022 refresh Plugs into the OBD-II port. Not for 2022.5 and newer refreshed trucks
Range DFM Module (GM Refresh) 2021-2026 GM SUVs and 2022.5-2026 GM 1500 trucks, 5.3L and 6.2L Connects at the ECM and also disables auto start/stop. CARB EO D-115-32 for 2021-2024 models
DiabloSport Sprint S1000 2007-2022 GM trucks and SUVs (pre-refresh), 2010-2024 Camaro V8, 2014-2019 C7 Corvette Plugs into the OBD-II port and overrides auto start/stop

Not sure if your 2022 truck is the refresh model? Range says the 12th digit of the VIN is 5 or higher on a refresh truck.

Range notes that some vehicles may still drop to zero-cylinder mode while coasting with its DFM Module installed, and recommends removing the module before a dealer visit or GM over-the-air update.

Option 2: Turn it off in a tune

DiabloSport and Edge handheld tuners can disable AFM or DFM as part of their tunes, so if you already run one you don't need a module. With HP Tuners, cylinder deactivation is turned off in the calibration in VCM Editor as part of your tune.

A tune is required if you've removed the AFM or DFM hardware (an AFM or DOD delete with new lifters and camshaft), because the computer still has to be told the system is gone. On 2019 and newer GM trucks the engine computer is locked, so a tune starts with an unlock; see does my vehicle need an unlock?

Which should you choose?

Your situation Best fit
Stock truck, you just want it to stay a V8 Plug-in module
Leased, or want an easy return to stock before dealer service Plug-in module
2022.5 or newer refreshed GM 1500, or 2021+ GM SUV Range DFM Module, or unlock plus tune
Already running, or buying, a DiabloSport or Edge tuner The tuner; skip the module
Modified, or planning to be HP Tuners MPVI4 + credits
AFM or DOD delete hardware installed A tune is required

Browse by vehicle

Frequently asked questions

Does an AFM disabler add horsepower?

No. It only keeps the engine from dropping cylinders. For more power you need a tune.

Can I unplug an AFM disabler and go back to stock?

Yes. The plug-in modules don't reprogram the factory computer, so removing the module returns the vehicle to stock behavior.

Will an AFM disabler work on a 2023 Silverado?

The Range DFM Module (GM Refresh) is built for 2022.5-2026 GM 1500 trucks. The Range AFM/DFM Disabler and the DiabloSport Sprint are not compatible with the refreshed trucks.

Do I need a module if I have a DiabloSport or Edge tuner?

No. Those tuners can disable AFM or DFM in their tunes.

Last reviewed: November 2026.